Why did my Vitamix blender shut off? Understanding motor heating (with data)

measuring-vitamix-motor-temperatureIf you’ve ever had your Vitamix blender abruptly stop working, most likely it was the thermal override kicking in. The thermal override turns the motor off before the motor burns out. Then, once the motor cools, you can run it normally again. It’s not a huge deal, but it’s best to avoid. (Depending on what kind of blending you do, you could easily use a Vitamix for decades without ever getting close to overheating. But, if you blend super thick foods, there’s a good chance it will happen at some point.)

If you have an Ascent or Venturist model, it will display error code E31 or E3x when the thermal override activates.

This post will explore what causes motor heating and describe how to minimize it. I investigated by directly measuring the temperature of the motor in a variety of blending conditions.

Why should you avoid overheating the motor?

  • If the thermal override trips, you cannot run the Vitamix until it cools, which can take 20–60 minutes. If you’re in the middle of making something, the interruption is a hassle.
  • Keeping the motor cooler should prolong its life. Occasionally overheating the motor is fine, but if you do it regularly, it puts more wear and tear on the motor.

If you don’t want to read all the details, here are a few key points:

Why did my Vitamix shut off?

Thick blends can overheat the motor. It will shut itself off before it burns out, and it will not let you turn it on until it cools down. To avoid overheating, don’t blend more than 4 cups of thick blends like hummus, nut butter, or ice cream. When blending thick ingredients, run at maximum speed.

If the motor does overheat, you can use it again sooner by blowing air into the vents with a fan or hairdryer (on cold!). Some people speed cooling by putting the Vitamix base in the fridge, but, if you leave it in too long, you could run into condensation issues when you take it out.

The rest of this post will explain factors that contribute to motor heating, why fast speeds are helpful, and a special motor-cooling trick.


Vitamix motors have the following properties:

  • The harder the motor works (e.g. with a thicker blend), the more it heats itself. This is because it draws more electric current at higher loads. (The amount of current draw has to do with the back EMF that forms in the motor.)
  • Thicker blends slow down the motor (see my speed measurement page for more details). This is why the motor sound has a lower pitch when blending thick things.
  • The motor is cooled by air blown by a fan on the bottom of the drive shaft, and the fan spins at the same speed as the motor.

You can see how a thick blend increases the chances of overheating: the motor heats more and has less cooling. For more information about the type of motors used in Vitamix machines, look up universal motors.

Factors that contribute to motor heating

You don’t need to obsess about these factors—just keep them in mind. The motor is most likely to overheat when multiple factors act together.

  • Thickness of blend (thicker = more heat).
  • Quantity of blend (more volume = more heat).
  • Blending time (longer time = more heat). You can get away with blending something really thick for a short time, but if you blend it for extended periods, it will overheat the motor. Similarly, if you make one recipe after another, the motor can be more likely to overheat, because it didn’t fully cool between uses.
  • Temperature of environment (hotter environment = less cooling by air) so you have to be more aware in the summer or if the kitchen is hot from a lot of baking.
  • Interestingly, humidity of the air does NOT matter.1

That brings us to motor speed, which I think is most interesting. Most Vitamix manuals have a statement like this one from the 7500 manual:

Tip: Blending too long at too low of a speed setting will overheat the machine and cause the Automatic Overload Protection to turn off the machine. Blending on higher speed maximizes the motor’s cooling fan to avoid overheating.

(Many people repeat a version of this and say that the cooling fan only runs when the Vitamix is set to high. But that is not true. The fan is connected to the motor shaft, so it runs every time the motor does. If you put your hand near the air outtake vents on the bottom sides of the base, you can feel air at all but the slowest speeds, where it is still blowing, but is less detectable.)

Vitamix’s speed recommendation is counterintuitive, and it inspired me to investigate by directly measuring the motor temperature.


I attached a small temperature probe to the motor stator with thermally-conductive double-sided tape, plus temperature-resistant tape over it to be on the safe side. I ran the wire out an air vent and recorded temperature over time using an Arduino.

I made a batch of 8 cups of thick syrup (similar to what I used for my horsepower measurement) to get a high load that would be consistent. One thing to watch out for with syrup is that its viscosity changes significantly with temperature, and it heats up during blending. But as long as you keep this in mind, you can ensure the syrup temperature is consistent across comparisons.

Here’s a simple temperature trace of the motor blending thick syrup for 1 minute, and then staying off:

blend-heavy-load-in-vitamix-then-let-cool-temperature-plotYou can see that it’s about halfway cooled after half an hour and almost completely cooled after two hours, but it takes about 8 hours for the motor to fully return to its starting temperature. The important takeaway is that motor heating becomes a more significant issue if you blend multiple thick things within about an hour, because the motor won’t have time to cool in between. [Curious why there is a bump at ~105°F?2]

I wondered if lower speeds would heat more due to the slower cooling fan, which would explain Vitamix’s high speed blending recommendation. So I made a series of measurements comparing motor heating at high and low speed. However, for a given load, high speed always heated the motor faster than lower speeds. This seems contrary to Vitamix’s recommendation! At first I thought maybe I wasn’t seeing the lower speeds heat more because the motor was too close to room temperature. (The greater the temperature difference between motor and air, the greater the cooling advantage of higher speeds.) So I made measurements at elevated motor temperatures, but again saw the same thing: high speed heated the motor more than low speed. This means that the lower electric current at lower speeds more than compensates for the slower cooling fan.

Then I realized that in most actual thick blending situations, the Vitamix does not run against a constant load. When making hummus or nut butter, the motor encounters a high load, and then the blades often form an air pocket. In the air pocket the blades encounter almost no resistance. Then you collapse the air pocket with the tamper, so the motor ends up going between high and low loads.

I figured maybe the air pockets only form at high speed. I tested with a batch of almond butter that was identical to my recipe write-up, except I blended it at low speed (setting 2 of 10). Sure enough, no air pockets formed at low speed. Here are the temperature plots:


The initial motor heating rate at low speed is less than at high speed. At that point the blades are chopping the nuts. But at high speed, as the nut pieces get tiny, they fly away from the blades and form an air pocket, and the motor starts cooling more. The low speed case ends up heating much more than the high speed one. (Also, the low speed almond butter never got fully smooth.)

This is the answer to the paradox of why high speed keeps the motor cooler. At high speed the blade is more likely to form air pockets, which allow the blade to intermittently spin at low load, which keeps it much cooler. (You can tell when the motor forms an air pocket because the sound changes to a high pitch whine.) There’s also a secondary aspect, which is that at high speed the motor will be able to finish the blending task faster, so it’s on for a shorter time.

The use of air pockets to cool the motor is a feature of Vitamix blenders that I didn’t know about until now. (The formation of an air pocket is not a problem because Vitamix machines come with a tamper that lets you collapse it without needing to stop the motor.) Now I’m wondering if Vitamix engineers designed the blades to form the air pocket for this purpose.

Advanced cooling trick

You can use this trick if you have a thick blend that is not forming air pockets or if you can sense the motor heating up. Sometimes you can smell the motor heating before the thermal override kicks in. (I noticed the motor smell when the windings got to ~167°F, and the thermal override kicked in at ~185°F.)

The trick is simple: stop the motor, remove the container, make sure that nothing is touching the drive socket, then turn the motor on high. Run it for ~60 seconds, and it will pull lots of air through without having to work hard.3 Just make sure nothing touches the fast-spinning drive socket. And remember to only move the container when the motor is fully stopped. Here’s a comparison of the motor cooling while turned off and cooling with 1 minute running with no container:


In this case, 1 minute of no-load blending cools the motor as much as waiting ~30 minutes without running. You can see the temperature quickly drops almost all the way to room temperature when running without the container. It increases after the motor stops because the thermometer measures the surface temperature of the windings. The temperature increase comes from conduction from the hotter internal windings.

One thing to watch out for is that the thermal override sensor also sits on the surface of the windings. So if you use this trick and immediately resume super heavy blending past the overheat temperature, the thermal override will be a bit delayed, and the motor could go above the ideal temperature cutoff. It shouldn’t be a problem if you wait a few minutes after the no container blend, or if you’re blending something only moderately thick. Also, if you use the trick preemptively, you can prevent the motor from getting close to the overheat temperature.


Thick blends cause blender motors to work harder, which makes them more likely to overheat. If you understand the basics of what’s going on, you can make thick blends without overheating. Running the motor at maximum speed reduces the chances of overheating by shortening blending time, and by periodically forming an air pocket around the blades, which allows the motor to efficiently cool itself. There’s one other thing I learned from these measurements: you don’t have to be paranoid about totally avoiding low speeds for thick blends—low speed will usually only be a problem if you leave it blending for extended periods over ~1 minute.

1. Interestingly, the heat conduction properties of air are not significantly sensitive to humidity.
I was surprised by this because, as humans, humidity influences our perception of temperature. But, apparently, that’s mainly due to confounding factors and clothing being less warm when it’s damp.

2. It doesn’t matter for this discussion, but I’m afraid the bump may be distracting. It is a repeatable feature of these temperature plots, and I think I know what causes it. Above that point the motor is hot enough that the other parts inside the base warm up as they absorb heat from the motor faster than they lose it to the environment. That bump is the point where the motor temperature has roughly equilibrated to the inside of the base. That temporarily slows the motor’s cooling rate. Then the rest of the base starts cooling, and the motor resumes its cooling.

3. For every combination of speed and load, there is a steady-state temperature that the motor would get to if you kept blending long enough. At that temperature, heat from the current in the windings is balanced by cooling by the fan. For high loads, that steady-state temperature is well above the overheat temperature. I measured the steady-state temperature of the motor at max speed with no container, and it runs about 14°F above ambient, which is much less than the overheat temperature. The current draw at maximum speed with no container is 2.6 A, compared to 12-15 A for high loads.

Did you enjoy this post?

Enter your email below to receive updates when new posts are published so you never miss new content. Emails are usually not more than once per week.

Or follow along on Twitter or Facebook: Twitter_logo Facebook_logo_29px


Why did my Vitamix blender shut off? Understanding motor heating (with data) — 54 Comments

  1. I have a Super 5000, which is 12 years old. I love it, but while using it the other day, the top got bumped hard and it had made a “zing” metal noise, as I instantly grabbed the container, picking it up while motor was running…..all within a second. I turned it off, and put the container back on. It would not start, even he next day. No burning smell! I thought the gears got stripped, but both turn manually, same as before. It’s like the on/off switch doesn’t work! Any help is appreciated!

    • Does the motor make any noise when you turn it on? If yes, an easy drive socket replacement would probably fix it. If it stays totally silent, then it would need to be repaired by someone who can open it up and test the various components.

  2. Why are there Recipes that would make your vitamix overheat by making to thick of it ingredients I followed the recipe as I went through it with the app an then hit blend and I got stuck making something that I could not finish

  3. I have had my Vita Mix for about 20 years. When my husband passed 3 years ago I stopped using it. Now it won’t do anything, turn on, move, nothing. Where can I take it to have it tested.

    • You might be able to find a local appliance repair shop, though those are becoming more and more rare.

      You could call up Vitamix and ask them how much they would charge to service it. I’m not certain how much they would charge, something like $150 or $250.

      Or you can take advantage of Vitamix’s trade-in program. If you buy a new (or reconditioned) machine, you can get a $100 refund by sending in your old machine. Just call Vitamix at 800-838-2649 to schedule the return.

  4. This article is so informative and helpful. Thank you so much!! I now understand what I’m doing wrong and how to avoid overheating my machine!

  5. Great post. I found this informative after I was worried that I blew out the motor. I appreciate all the tips as well. I would have thought low speeds would keep it cool on big mixes, and when I had air pockets I was not sure what that would do to the motor. Well done!

  6. Great article! It saved me from sending my lovely Vitamix to a service.
    I was scared of the high pitch whine while mixing on speed 10 but now I know it is necessary and I won’t avoid it.
    Thank you very much!

  7. Great article! Unfortunately, in the new Vitamix models it is not possible to start the engine without a container. Will the active cooling trick also work with an empty container?

    • Yes, but it’s not great for the bearings to run them too long with an empty container.

      There is an extra advanced trick for the Self-Detect models (totally unsanctioned by Vitamix). Lift the container off the base, rotate it 45 degrees, then set it down on the four posts. Now you can run the motor without spinning any blades.

  8. This was a good article, thanks for doing the research to explain what factors into overheating, and how to minimize it. This gets me thinking of other ways to deal with the problem. One idea that crossed my mind was would having something like an Air Hockey Table underneath the blender with it’s pin holes blowing air up that could be used to actively cool the blender even when the blender is not running. I did a bit of a internet search but was unable to find product the size of a blender base, nor any hacks that had figured that out. If anyone figures out a solution like that be sure to post.

  9. Hi, I have adventurist model 1200. We moved last Nov, after the new year I finally unpacked my blender and each time I tried to use it, it came up with error codes. I’d turn off and wait, and it did same thing, even tried different sockets in kitchen. Long story, but contacted Vitamix and they sent me label to return for repair. After getting it back, it did the same thing, so repeat the process and again same thing. Sent back a 3rd time and they replaced my blender. Great, but guess what same thing. Error code 31. Give over hour to cool, tried different outlets but nothing. It started up a few times, but immediately went to error code 31. I hear a faint click if I try now. Could there be a possibility it is the electrical wiring in the panel of my house. Something wrong and it just cuts it off? I’m afraid Vitamix will not be too happy too hear I am still having this problem. Any ideas?

  10. This was extremely helpful in helping me understand how to take care of my Vitamix. And very reassuring as I’ve only had my Vitamix for a couple weeks and thought I just broke it tonight. Thank you for sharing your research.

  11. My Vitamix died tonight.I let it cool all day !! A3500 Ascent series Model VMO185. This is my 4th or 5th one.. Do they tend to blow up every 4-5 years ?? I only make 1-2 smoothies a week, sometime less… Should I just toss it or is it worth trying to fix it.. What’s the average cost to rebuild the motor? I know you have a trade in but at this time it’s not possible being on a fixed income and inflation combined.. I lived in Cleveland for 45 years but I’m in South Carolina now and shipping costs would be prohibitive… Let me know.. I guess I’ll have to start buying the premade shakes… thanks

    • You should call up Vitamix and see if your machine is under warranty. There’s a good chance that it is, and Vitamix will fix or replace it for you for free.

  12. Since their machines create a lot of friction and heat, Vitamix should use liquid cooling. It is more efficient than fans and fins.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.